ten10 Projects
To achieve perfect aim, just shoot then call anything you hit as target.
Friday, October 1, 2010

DIY Watch Collector's Box

Note: I've been designing and handcrafting horology-related accessories since year 2000. I'm doing this for a living. The articles and instructions found in my blog here are shared with you through personal experience; projects shown are all simplified alternative methods designed to make it easier for a beginner. My apologies for not showing you the exact way of how I got things done. You know the reasons. If you would like to custom-made watch winders, watch-strap holders, watch collector's case or boxes, you can email me @ furnicraft(underscore)boutique at yahoo dot com

------------------------------------------------------------------------------------------------------------

So now you want to get organized and don’t wish to spend money on commercial watch boxes. DIY could be your hobby and you have decided to be stingy and make a cheap box for your expensive collection; or maybe your watches aren’t that expensive. Or perhaps the shoebox you were keeping them in had mushrooms growing and had to throw them away. Where else could you keep your precious timepieces?


Look no further; here are the 16 steps to make your own watch box.

Tools required
Sharp utility/art knife
Contact Glue
Try square
Marking pen or carpenter’s chalk
Steel rule
Cloth scissors
Patience and
Lots of imagination


Materials required
Wooden box (your preferred size)
Velvet or satin (I use both)
Laminate Foil with wood prints
Artcard or stiff cardboard

 
Step 1

a) Scout around for two small boxes that would be sufficient to house the number of watches you have. One box for the cover and the other for the base.

I picked two boxes from Daiso that were kind of “nested” and could comfortably house three bulky watches. That’s the only available ones that suit the purpose.

b)  Start by measuring the external and internal dimensions of both boxes and write it down.


Step 2

a) Start with one of the boxes first. I started with the base which was the smaller of the two.

b) Cut strips of satin cloth to size slightly longer and wider than the length and width, just to cover the upper part of the box. There should be 4 pieces.

c) Spread contact glue across this strip of cloth and paste it on the box.

d) Trim the edges of extra cloth or frays with a cloth scissor.

e) Don’t worry about the uneven edges. This will be taken care of later.

 
Step 3

a) Cut 4 pieces of artcard for the two lengths and two widths. This is the first layer of outer skirting for the base.

b) Cut 4 pieces of velvet just enough to cover the top portion of the artcard.

c) Paste the velvet on each of the 4 artcard using contact glue.

d) Leave to dry for about an hour.

 
 
Step 4

a) Paste the first layer skirting you’ve prepared on each side of the box, over the satin cloth.

b)     Press firmly to position all four sides. Leave to dry for an hour.


Step 5

a) While the pieces are drying, start cutting pieces of artcard for the second skirting layer. This should be the length I cut 5 pieces of artcard for each dimension so that they match the thickness of the top cover.

b) Paste the 5 pieces together with contact glue. Drying time is 1 hour.

 
 
Step 6

a) Unpack the laminate foil. I use this type shown in the picture below.

b) Measure the “new” external lengths and widths of the base box after you’ve pasted the 1st layer skirting.

c) Cut strips of laminate foil and paste it over each piece of the 2nd layer skirting.

d) This also has to be enough to cover the edge of the artcard strip.

When pasting, try to be as straight as you can.
 
 
Step 7

a) Once all four are completed, paste them on the four sides of the base box. This forms the outer skirting of the base.

Noticed I’ve made the height shorter than the 1st layer?
 
b) I’ve made the length-wise strips slightly longer than the widths to hide the joins when they come together.

c) Once the four sides are pasted, they should look something like this.

Outer skirting completed
Step 8

a) In the same manner, cut strips of artcard and velvet to paste them on the insides of the box.

b) Don’t rush - measure, cut and paste one side at a time. My principle - Measure twice but cut only once!



Step 9

a) Next, we have to make the inside-base for the box.

b) Measure the internal L x W and cut 1 piece of artcard to size.

c) Cut velvet to size and paste it over.

d) Position the completed base board and press firmly to the base.

 
 
Step 10

a) Next step is to make separators or dividers for the base box.

b) Measure the internal dimensions. Using some math, calculate the required size of the separators and the quantity required. This depends on the box size and the number of watches.

c) Using your new acquired cutting skills, cut the required number of separators and form a “block” such as this shown in the picture below.

I’ve inserted another piece of artcard to strengthen the internal structure of this block.


Step 11

a) Cut pieces of velvet to cover just the longer sides of the “block”. The shorter sides can’t be seen once placed inside the box.

b) Put contact glue on the base of the block and insert into the box. Press gently but firmly to let the glue settle in.


c)     If some extra velvet seems to jut out, just use a toothpick to tuck it in gently.



Step 12

a) When inserting the other separators, use some kind of measuring device which helps you position them accurately. I made a simple one using discarded pieces, shown below. The widths are slightly smaller than the watch pillow so that there'll be a snug fit.

 

Step 13

a) This is the second last step for the base box.

b) Cut laminate foil to cover the entire length of the exterior. It must cover the exterior in one piece. Using four separate pieces would not be aesthetically pleasing to the eye.

c)     Keep any balances in a roll for future use.

 
Step 14

a) Carefully paste the cut foil around the box. Ensure no air is trapped under the foil during pasting.

b) Trim-off any excess foil.

c) Sorry I forgot to take pictures of this step.

d) You’ve now completed the bottom half of the watch box.

 
Step 15

a) Again I forgot to take pictures of this step, must be my age catching up.

b) Anyway, cut a piece of laminate foil slightly bigger (about 1cm) for the upper surface of the top cover. This laminate foil is self adhesive.

c) Slowly position it on the top cover and paste it. You could also lay the foil on a table and gently lower the top cover on it.

d) Ensure no air-bubbles trapped.

 
Step 16

a) Cut length-wise a long laminate foil strip, the size of the entire top cover length, meaning both lengths and both widths. Cover it in one go.

b) The foil I bought has a big ugly crease across the width (see picture below). I literally ironed it out. Use a clothes iron set to “SILK” and place a double layer cloth over it. Iron it for just 5 ~ 10 seconds. Repeat if needed. Allow to cool before pasting otherwise the foil will be stretched to an irregular shape.

c) Paste it slowly across the entire length. A little lateral tug is required too.

 
Once completed, the top cover should look like this. I wanted the beautiful "grain" to be slightly off-centered.
d) Tuck in all the four sides. Use your fingers to level any uneven corners or edges.
 


A BIG Congratulations for completing yet another project!

Note: - Similarly, any other box could be crafted to become a watch box following close to these steps. But for a professional looking (more refine) watch collector’s box, they are available in stores or I could custom-built one for you.

Our next project would be to make DIY Watch Pillows. Stay tune folks.


shalom!

Labels:


posted at 1:01 AM by ten10


My Profile

Archives

Sep 28, 2009
Sep 30, 2009
Oct 4, 2009
Oct 7, 2009
Oct 11, 2009
Oct 14, 2009
Oct 17, 2009
Oct 18, 2009
Oct 20, 2009
Oct 23, 2009
Oct 26, 2009
Oct 29, 2009
Nov 2, 2009
Nov 6, 2009
Nov 10, 2009
Nov 13, 2009
Nov 16, 2009
Nov 20, 2009
Nov 23, 2009
Nov 27, 2009
Dec 1, 2009
Dec 4, 2009
Dec 7, 2009
Dec 10, 2009
Dec 18, 2009
Dec 24, 2009
Jan 3, 2010
Jan 8, 2010
Jan 12, 2010
Jan 16, 2010
Jan 20, 2010
Jan 22, 2010
Jan 27, 2010
Feb 1, 2010
Feb 5, 2010
Feb 18, 2010
Feb 24, 2010
May 3, 2010
May 8, 2010
May 12, 2010
May 17, 2010
May 31, 2010
Jun 5, 2010
Jun 9, 2010
Jun 13, 2010
Jun 18, 2010
Jun 22, 2010
Jun 27, 2010
Jul 4, 2010
Jul 9, 2010
Jul 29, 2010
Aug 8, 2010
Aug 12, 2010
Aug 19, 2010
Aug 31, 2010
Sep 4, 2010
Sep 9, 2010
Sep 22, 2010
Sep 25, 2010
Sep 28, 2010
Oct 1, 2010
Oct 9, 2010
Oct 14, 2010
Oct 15, 2010
Nov 5, 2010
Nov 14, 2010
Nov 19, 2010
Nov 28, 2010
Nov 30, 2010
Jan 17, 2011


home

Recent Entries

The Mystery of Turns Per Day
JOIN ME
Circuit for AC Watch Winder
Part 3, Special Watch Display - The Housing
Form, Fit and Function of a Watch Winder
Part 2, Special Watch Display - The "Sensor" Circuit
Blog Break
Panerai Watches on Watch Winders
There's Technology inside a Watch Winder
DIY Watch Collector's Box


Sites I Visit

All About Circuits
Chad the Watch Guy
Chronocentric
Circuits Today
Complaints Board
Dardel Paris
DIY Electronic Projects
Electronic Circuits Projects
Electronic Zone
Electronics Projects
Fratellowatches
Horology Zone
Horozima
MetkuMods
Paneristi
Perpetuelle
Public Warehouse
RED Free Circuits
Talking Electronics
World of Time
Carbon Watch Winder


Watch Winders

Abest
Arcera
Brown Safe
Buben & Zorweg
Cradle of Time
Dottling
Eilux
Elma Motion
ERS/Bocano
Erwin Sattler
MTE
Orbita
Penelop
Rapport
Roytec, China
Scatola DelTempo
Swiss Kubik
UB Sammerl
Underwood
Wolf Designs


Credits

design by maystar
powered by blogger